Posted on

top marijuana plants

Top marijuana plants

Top and FIM your plants with accuracy and ease using these Curved Trimming Scissors. The sharp blades slice through cannabis stems without leaving a mess behind—allowing plants to recover swiftly.

Secondary shoots are juiced with the growth hormone that previously would have been used to develop the main stem. However, most growers report that fimming is slightly less effective at reducing stretching than topping. A fimmed cannabis plant can still grow rather tall, albeit with far more top colas.
Another oft-overlooked and obvious problem with encouraging the formation of multiple fat colas is that marijuana plants tend to become really top heavy. In the absence of a ScrOG, plants may require staking with bamboo for support.

Top and FIM your plants with accuracy and ease using these Curved Trimming Scissors. The sharp blades slice through cannabis stems without leaving a mess behind—allowing plants to recover swiftly.
Topping cannabis requires accuracy, precision, and cleanliness. Snipping your plant with a blunt tool can cause the stem to break and it can leave a much larger wound than intended.
Instead of forming a solitary central cola, the plant will now grow two separate branches—the main cola will not continue to grow and the two side nodes will take over as colas.
Fimming involves pinching or cutting off around 75% of the tip of a plant. The very word FIM stands for “f*ck I missed”, and hints at how sloppy the technique appears. It looks as though the grower messed up their topping attempt! Looks aside, it’s an extremely simple and effective technique.
To top a plant, make a clean cut to the tip of the main stem using sterile scissors and fully remove the top growth. Be sure to leave about 5cm of space between where you cut and the lateral branches. This will give you slight room for error and help you avoid accidentally severing these important structures.

Topping is the process of pruning the growing tip of the main stem of a cannabis plant. This is perhaps the most common HST or high stress training technique applied by both indoor and outdoor growers. Marijuana growing naturally will typically take on a Christmas tree structure; One dominant, main central cola and multiple sets of side branches. All plant parts receiving a share of sunlight at some stage during the day as the sun traverses the sky.

Push your marijuana into maximum overdrive with high yield pruning methods. This one is all about Topping and Fimming cannabis plants.

Top marijuana plants

What if my plant is already too tall in the flowering stage?

If you’re still in the vegetative (non-budding) stage and plants are growing way too tall, you can top the plant immediately to remove height as needed. The time spent growing the extra growth will be lost, so this may add time to the veg stage.
My suggestion is to use bending (LST) your plant to control the height of further growth.

The two growth tips that remain will each develop into their own stem. Each stem can turn into a bud/cola in the flowering stage, so by topping the plant once or a few times, you increase the total number of buds sites under the grow light, and it also helps you keep the plant flat and wide.
When you see your plant thicken connections like this, it means that the plant is strengthening the “internal system” of the stem, so it’s easeir to deliver nutrients and other building blocks. This results in faster growth, bigger colas, and increased yields for each of the affected stems.
Growers use the plant’s natural response to topping to produce short bushy plants with many colas. After the plant has been switched to the flowering stage, the widespread of colas allows the plant to efficiently use indoor grow lights to produce the biggest yields possible.
Topping should only be used in the vegetative stage! In fact, any training technique that involves cutting or damaging your plant should only be done in the vegetative stage of cannabis growth, and never during the flowering/budding stage.
Topping is a cannabis plant training techniques that involves cutting off the top of a main stem. The technique is designed to give you a free way to create more colas as well as spread out the plant so you can take advantage of all your light. As a result, topping can help you achieve bigger marijuana yields!

  • Cut off top of plant at stem in between nodes
  • Creates 2 main colas at the top of the plant, and LST can be used to create more
  • New colas are evenly spaced (attached to the stem in the same place)
  • Can be used to reduce the height of plant in vegetative page
  • Can slow down growth for a day or two

Topping Cannabis Guide: How to Top Your Plants Cutting Cannabis For Better Structure: “Topping” Topping is a cannabis plant training techniques that involves cutting off the top of a main