Posted on

how to pack a bowl in a pipe

How to pack a bowl in a pipe

Pack your bowl. (Photo by: Gina Coleman/Weedmaps)

4. Ash your bowl. When the marijuana has all been burned, dump out the ash so your bowl is ready to be re-packed for your next session.
The best way to accomplish this is with a grinder. If you have a grinder, place a medium-sized nug into the chamber where the grinding teeth are located. Put the cap back on and twist it back and forth until the nug is completely ground. If you do not have a grinder, you can use a pair of clean, sharp scissors or your hands to break your nug into small, evenly-sized pieces.

Glass pieces are not as mobile or discreet as other methods of smoking. Even small glass pipes like chillums get dirty and smelly after a few uses, thanks to the sticky resin that coats the bowl or pipe after smoking. This makes glass hard to carry with you or use for on-the-go smoking.
Bowls look and function a little bit differently depending on if they’re used in a regular pipe or in a bong. Bowls on the end of a pipe typically have a hole on the side called a carb . The carb plays a key role in controlling airflow, so you can let the pipe fill with smoke and then clear it when you’re ready to take a hit. On the other hand, bowls used with a bong usually do not have a carb. Instead, you control airflow by sliding the bowl in and out of your bong’s downstem .

  • Marijuana
  • A grinder
  • A pipe with a bowl on the end. The simplest kind is called a “spoon pipe,” but there are also variations, such as bubblers which include a small water chamber in addition to the bowl and body.
  • Depending on your smoking preferences, you may need a bong with a downstem and bowl.
  • A lighter or hemp wick to combust your marijuana
  • As an extra option, you can use a tamping tool to more evenly pack the marijuana into the bowl.

3. Smoke your pipe. Hold the bowl in one hand with your thumb covering the carb hole. Place the pipe to your lips. With your other hand, use a lighter or hemp wick to light a corner of the bowl. Once the weed sparks, pull the flame away and begin dragging in with your lungs. When you’re ready to inhale, remove your thumb from the carb and give a big drag. All the smoke that has built up inside the pipe will now rush into your lungs.
A bowl is one of the main components of a pipe or bong . Specifically, a bowl is the rounded-out part into which you pack your marijuana. The name of this component comes from an obvious source—a bowl is basically a small dish or basin designed for holding cannabis.

Smoke your pipe. (Photo by: Gina Coleman/Weedmaps)

Smoking a bowl is a classic method for smoking marijuana. Bowls are mainstays in cannabis culture. Here’s everything you need to know about packing and smoking a bowl.

Ideally, for the smoothest smoking sesh, don’t break up any weed, by hand or grinder. Simply hand-select the smallest nugs that will fit in your bowl, press them in, and voila!, you’ve got gentle, lightly flavored smoke rolling across your taste buds.

Breaking up buds by hand can be a time-consuming and painful task, especially if you’ve got larger hands or bigger-than-average fingers. Crushing a gram-sized nug is usually easy, but as it breaks down into smaller pieces, or as you begin breaking up smaller nugs closer to the bottom of the bottle (or plastic bag, for those of you in outlaw states), your fingers may get sore. However, if you prefer breaking up weed by hand, you’ll never need to worry about carrying a grinder around, or having to clean a grinder once it gets gunked up with resin.
To remedy a bowl packed too tight, poke the bowl with a straight, thin poker-ma-bob (a paper clip, a hair pin, hanger, a dab wand). Or, if you’re able to cover the bowl with your thumb or palm, cover it, then blow out of the pipe (don’t do this with a water bong, or you’ll just shoot water up into your weed, which will then either land on you or the ground. And then you or your surrounding will smell like bong water. Blah!). You should blow the hole at the bottom of the bowl clear while still retaining the contents in the bowl (because you covered it, remember?).

The advantage of using grinder to pack a bowl is uniformity and efficiency. It’s efficient because grinding weed is a fairly quick and straightforward process. And it’s uniform because all the weed has been ground up to equally sized pieces, so there are no little lumps or chunky bud-bits to deal with. It will ultimately lead to a more even burn, too.
Before we light up, let’s quickly review what a bowl is. The term bowl may or may not predate cannabis culture (and when does that begin, exactly?), and its use began at least two centuries ago. A bowl refers to the part of a pipe or bong that holds the smokable material, typically tobacco, but if you’re at MERRY JANE, we’ll be sticking to weed, thank you very much.
A well-packed bowl should stay cherried after it’s first lit, allowing everyone in the sesh circle to draw smoke from the pipe without having to flick a lighter every time. (Admittedly, tokers love to talk, too, and tangential conversations during the sesh may require lighting the bowl between each and every hit. And that’s perfectly normal.)
Ideally, you should fit as much weed into your bowl as possible while still maintaining proper air flow, and not spilling good herb all over your lap every time you pass the pipe.
Whole Hog

Not all bowls are created equally. Some massive bowls, sometimes called “party bowls,” can fit an entire eighth-ounce of buds. Some teeny tiny bowls, affixed to “sneak-a-toke” one-hitter-type pipes, may not have much room for any additional finagling. You’ll need to assess your bowl’s size and shape to optimize how it should be packed.

Believe it or not, there’s more than one way to pack a bowl of bud in your favorite pipe.