Posted on

diy cbd vape juice

Diy cbd vape juice

Once the isolate has been fully incorporated in the PG it’s time to add the 12ml of VG. Give the bottle one final shake of about 2 minutes and your CBD vape juice should be ready to vape.

Make sure you prime the coils and fill your tank with e-liquid, just like in the case of standard nicotine juice. We recommend a mouth to lung atomizer at first and if you’re OK with the flavor then swap it for a direct lung device.
For the 60PG – 40VG ratio you will need to measure out 18ml of Propylene Glycol and 12ml of Vegetable Glycerin. If you decide to use flavorings, these are usually PG based and you will need to subtract the amount of flavor from the amount of PG. For instance 10% flavor is 3ml, therefore we only need to use 15ml PG and 3ml flavoring.

To make your own CBD e-liquid you only need a handful of supplies: pure VG, pure PG, CBD isolate, an empty 30ml glass bottle, a blunt needle syringe and some flavoring.
Making your own vape liquid with CBD is easier than you would think. If you have the proper ingredients and some tools you are good to go. In this article we will show you exactly how it’s done.
Any standard vape juice is made out of four main components: Vegetable Glycerin, Propylene Glycol, Nicotine and Flavorings. CBD eliquids are made using roughly the same ingredients, only that they swap the nicotine for CBD isolate.
The key to crystal clear CBD e-juice is to dissolve the isolate in PG and add the rest of the ingredients afterwards. For this you will need to pour the 18ml of PG inside the bottle – or the 15ml PG + 3ml flavoring – and then add the isolate crystals. Put on the dropper cap and vigorously shake the bottle for about a minute or so.
High concentration Cannabidiol e-liquids tend to be quite expensive regardless of the brand, and many people simply cannot afford paying $100 for a single 30ml bottle. But what if there was a way to enjoy them for a more reasonable price? If you don’t mind a bit of DIY work, here are 5 easy steps to make CBD vape juice at home.

CBD isolate is cannabidiol in its purest form. It’s a crystalline substance, that looks and feels like a fine white powder. It has a concentration of 99% and it contains virtually no THC or any other substances. It also doesn’t include the terpenes and organic compounds which naturally occur in the plant.

5 Easy steps to make CBD vape juice at home – DIY Cannabidiol e-liquid Making your own vape liquid with CBD is easier than you would think. If you have the proper ingredients and some tools

Diy cbd vape juice

Now that you’ve added CBD into the vape, you’re probably wondering how to add some flavour! This is where we bring terpenes into the mix. We’ve previously touched on terpenes and their many uses. They’re the smell and taste of individual strains of cannabis, extracted in a liquid form. They are incredibly concentrated and powerful, so only a few drops are necessary to add strain profiles to your CBD vape juice. Terpenes are present in all foods, they can influence our behaviour so much so that casinos in america have added them into diffusers to influence gamblers gambling habits! The following image shows the different terpenes found in several strains – for legal reasons we must state that no medical claims should be derived from this, we are not medical consultants, we’re just sharing what is already in the public domain and implore anyone interested in legal cannabis to get medical information from their GP.

1. Using a scale, measure 0.5g of crystals and crush them up into a fine powder – either with a pestle and mortar, or just a blunt edge.
3. Empty your crushed crystals into the warm vape juice, stir and steep until the crystals are fully dissolved.

If you are trying to make your CBD vape juice from scratch then we recommend starting off with 30ml of Vegetable Glycerin and proceed to heat it up and dissolve your crystals in the oil.
2. Mildy head up your vape juice – we rest ours against a radiator for an hour, if your impatient you can place your vape juice in a glass bottle in a microwave for a few seconds.
Our CBD isolate crystals are 99.9% pure CBD, and completely THC-free. They are fat soluble and can be dissolved into all oils, not just vapes. 1g of CBD isolate is approximately 1000mg of CBD. High quality crystals have CBD counts above 90%, ours are among the highest quality in the world. Low quality crystals are brown/yellow in colour due to inefficient crops and extraction methods that leave behind non-CBD residue. Below we instruct how you can make your own 500mg strength CBD vape juice with crystals:
FLAVOUR!
For those who prefer to have control over the ingredients and overall strength of their vape juice, CBD isolate crystals are perfect. By dissolving them straight into any vape oil, they can very easily turn an everyday vape juice into a supercharged CBD liquid.

Our in-house recipe is to add 0.5ml of terpenes to every 10ml of vape oil, and let it steep for 48 hours for equal flavour distribution. Our terpenes are the first of their kind in the UK – they’re actually extracted from cannabis, unlike most on the market that are synthetic and isolated from fruits and vegetables. Read up on the “entourage effect” and soon you’ll be adding terpenes into all your Cannabis products to increase their potency.

For those who prefer to have control over the ingredients and overall strength of their vape juice, CBD isolate crystals are perfect. By dissolving them straight into any vape oil, they can very easily turn an everyday vape juice into a supercharged CBD liquid. Our CBD isolate crystals are 99.9% pure CBD, and completel